Posted on

Here is how you can make pocket knives in different ways

Having a pocket knife can be very useful whether you are using it for protection or just as a traveling accessory. For people who have a hobby for hunting, a pocket knife and a Pinty scope for the rifle are the two most important things one should have. In the article below, we will talk about how you can make your own pocket knife from scratch.

There are probably as many methods for making a pocket knife as for skinning cats. We should also differentiate between the methods employed by professionals and factory workers and those employed by amateurs. 

It may be difficult, but it’s not impossible to become an expert pocket knife maker. However, until more complex methods are available, a need for relatively simple methods exists. These are methods one is likely to have on hand already. Knives can be purchased from knife-making supply stores or at local hardware stores.

Spare Change Into knife

You can combine nickel and pennies to create a rudimentary knife. To loosen the nickel and increase its surface area, hammer it on an anvil. Make a pattern for a blade with a handle that sticks out using a good gel pen. You can choose what size you want. You can then take your hacksaw and take the excess coin out.

Bend the pennies in the vice until you can fit them around the nickel handle you made and tighten them. If you want to wear the face off the penny, use a medium-level abrasive grinder. You’ll need both to maintain the blade’s sharpness. Make the blade smooth and shiny using a polisher, and you’ve got your six-cent knife.

You can master this challenging aspect of making Pocket knives in this article, allowing you to focus on other parts of the design.

A wood-handled folding knife

Using the pattern for the knife handle, blade, and pinholes, print or draw them out and cut them out. Glue them to an eight-inch thick hardwood slate, and then use a hacksaw to rough cut the knife parts. Once you’ve trimmed closer to the lines, file down the edges of all the parts. Including the knife blade. Check that everything is aligned correctly by drilling through the pinholes again.

You can purchase a spring block at a knife parts store that will assist the blade in opening and closing smoothly. Then that pinhole-sized dowels can be put through your dowel maker to be sanded and shaped before they can be inserted into the holes and trimmed. Let the glue dry before inserting the pins. As an alternative to oil, you can use a wood stain.

knife with a steel blade and a liner lock mechanism

The blade is made of hardened steel. The handle is made of Micarta. The pins that hold the blade in place and the spring are made from titanium. The only tools you will need are basic tools and a ball-peen hammer.

It should cost around $25 for the whole project. Just print and cut out your designs. Cut the metals around the glue dots with a hacksaw. Do not remove the stop pin or the lock from around the glue dots- you can always trim off the extra space later on.

Then file it to a fine sixteenth-of-an-inch point (dime width) by tracing the exact center of the knife edge. Polish the remainder of the knife as necessary. Drill straight when drilling the pivot and stop pinholes.

The holes must line up correctly in order to produce a properly functioning knife. To get the drill bit started easily in the correct spot, punch a small hole in the center of the area to be drilled out. If you first drill several close-together holes to give the hacksaw an entry point, you can cut out the T-shape of the titanium lock piece with a hacksaw.

A knife blade and lock can only fit snugly together with some trial and error. If they don’t, file them and retest. However, be aware that the grooves above and below the end of the blade that touches the handle will need to be adjusted little by little until they are just right. Also, if the corner point is too long in the same area, the blade will not fold. Once you’ve inserted the pins and made sure the knife folds and unfolds properly.

Hacksaw with two blades and PVC knife

A PVC pipe handle is used to hold blades created from flattened hacksaw blades. Two half-inch pop rivets and a washer on each side hold the knife together. You can occasionally cool the hacksaw material by dipping it in the water while grinding.

Fold the PVC pipe around both blades by partially melting it over a burner. While attaching the knife, make sure to put three hacksaw blades into the hole as you drill the hole.

The blades can now be turned freely without the third piece in the way of their rotation. Pocket knives have been made and used by men since ancient Roman times. The person who makes such a tool is producing a good tool and developing a new hobby. He is also carrying on an old tradition.

How does spring affect a folding knife?

By adding a spring to the blade, it will be easier to open and close it while retaining its position.

A spring does not always hold the blade of a folding knife. As an antique, simple design, the Capucin requires only two nails, whereas the Piedmonts use a friction system aided by the position of the thumb on the heel of the blade. For the Opinel and the Nontron, this is a rotating ferrule that locks the blade. Other folding knives use different spring shapes, just as there are different locking methods.

How to Care for Your knife

The surfaces of pocket knives are rough. All kinds of substances can cover a blade, including dried sap, fruit juices, adhesives, dirt, and pocket lint. It’s also possible that joints will become harder to open, and steel will rust. If that happens, there are easy steps to follow.